Physicochemically modified polymer-based fluidic gates with tunable wetting properties for intelligent liquid manipulations
Available online 8 November 2024
The creation of a selective flow path and the regulation of a flow rate are of critical importance for polymer-based devices that manipulate liquid at the microscale. The formation of a 3D interconnected...
Share article
Compatibilization phenomenon in polymer science and technology: Chemical aspects
October 2024
Polymer blends are mixtures of two or more macromolecular species – polymers and/or copolymers. They are used to increase the range of properties available from existing polymers without synthesizing...
Share article
Time- and temperature-dependent mechanical and rheological behaviours of injection moulded biodegradable organoclay nanocomposites
October 2024
Injection moulded specimens were produced from biodegradable poly(butylene succinate) (PBS)/organomodified montmorillonite (OMMT) nanocomposites, after melt compounding in different compositions. WAXD...
Share article
Compatibilization of biopolymer blends: A review
October 2024
Biopolymers from renewable bio-based resources provide a sustainable alternative to petroleum-derived plastics, but limitations like brittleness and cost restrict applicability. Blending offers an affordable...
Share article
Is compatibility critical in polymer engineering?
October 2024
The paper focuses on the necessity for compatibilization in polymer blends and composites due to the differing chemical nature of the components, which causes antagonism on the contacting surfaces....
Share article
Effect of nanofillers addition on the compatibilization of polymer blends
October 2024
The recent interest in multifunctional materials with tailorable performances led to the formulation of novel polymer blends, with enhanced properties with respect to traditional plastics and showing...
Share article
Strategies for compatibilization of polymer/waste tire rubber systems prepared via melt-blending
October 2024
Waste tires are a low-cost and high-calorific alternative fuel, therefore energy recovery is still very popular method of their utilization. On the other hand, waste tires are composed from high quality...
Share article
Compatibility issues in high voltage DC cable insulation development
October 2024
In the last decade, growing efforts were made to replace crosslinked XLPE insulations with thermoplastic ones in high-voltage DC cables. The main reason for these development projects is the injection...
Share article
Polymer compatibility and interfaces in extrusion-based multicomponent additive manufacturing – A mini-review
October 2024
One of the most widespread versions of additive manufacturing technologies (AM) is fused filament fabrication (FFF) or fused deposition modeling (FDM), using polymer melts to print freeform structures....
Share article
Synergistic Effects of Psidium Guajava and Copper Nanoparticles Reinforced Hybrid Hydrogel for Tissue Engineering
Available online 12 October 2024
Hydrogels are biopolymers proficient in engrossing much water in their 3D network structure. However, single-polymer hydrogels frequently experience poor physio-mechanical properties, confining their...
Share article
Graphene Nanoplatelet Induced Microphase Separation in Poly(ether-block-amide)s
Available online 12 October 2024
The inclusion of graphene nanoplatelets (GNP) in segmented block copolymers offers a route to manipulate microphase separation for tailoring the mechanical properties of thermoplastic elastomers. GNP...
Share article
Engineering flame and mechanical properties of natural plant-based fibre biocomposites
Available online 29 August 2024
The escalating global concerns surrounding unsustainable petroleum consumption have fueled interest in natural plant fiber polymer biocomposites (NFPCs) as eco-friendly alternatives. NFPCs offer advantages...
Share article
Advancements in Poly(ionic liquid) composites with carbon nanomaterials
Available online 27 August 2024
Carbon nanomaterials have become essential in modern daily life. Their porous nature and good electrical conductivity are critical for composite applications. However, their inherent van der Waals forces...
Share article
Intramolecular cooperation and biphasic flame retardant mode of action: Effectiveness of hexa(1,2,4-triazol-3-ylamine) cyclotriphosphazene in epoxy resin
July 2024
The substitutional structure of cyclotriphosphazene derivatives significantly influences their flame-retardant effectiveness. A cyclotriphosphazene derivative with triazole group, referred to as hexa(1,2,4-triazol-3-ylamine)...
Share article
Surface grafting POSS to improve the hydrophobicity and fire safety of polyrotaxane based smart phase change materials
July 2024
Polyethylene Glycol (PEG)-based flexible phase change materials have broad and practical application value in thermal management of flexible electronic devices. Considering the typical application cases...
Share article
Fire performance durability of flame retardants in polymers and coatings
July 2024
The fire performance durability of products containing flame retardants may be significantly affected after aging and mechanical recycling. Publications of the last ten years show that even under severe...
Share article
Review of thermal conductivity in epoxy thermosets and composites: Mechanisms, parameters, and filler influences
July 2024
Rapid development of energy, electrical and electronic technologies has put forward higher requirements for the thermal conductivities of epoxy resins and their composites. However, the thermal conductivity...
Share article
Advances in flame retardancy of asphalt pavement: A review
July 2024
Asphalt pavement is widely applied to the surface in high-grade highway tunnels due to its prominent preponderance in road performance. However, asphalt is flammable as the binder material to adhere...
Share article
Improving the flame retardancy properties of PLA/PC blends
July 2024
Polylactic acid/Polycarbonate (PLA/PC) blend was prepared via twin screw extruder by taking the bio-based content as much as possible and the better mechanical, thermal, and impact properties into consideration....
Share article
Simple modification of phenylphosphonic acid to construct polyester-cotton fabrics with high flame retardancy
July 2024
Polyester-cotton fabrics (PTCO) have excellent properties and are ubiquitous in daily life, but their serious flammability brings great safety hazards to people's lives. This study used phenylphosphonic...
Share article
Novel four-in-one intumescent flame retardants for polypropylene: Synthesis, characterization and properties
July 2024
To address the shortcomings of traditional intumescent flame retardants (IFRs), a novel four-in-one IFR (M [APP/NiCo2O4]) was constructed for the first time. It integrates acid source, gas source, carbon...
Share article
Magnetic-responsive triple shape memory polymer from bio-based benzoxazine/urethane polymer alloys with iron oxide nanoparticles
Available online 25 July 2024
Novel magnetic-responsive triple shape memory polymers (SMPs) derived from bio-based benzoxazine-urethane (V-fa/PU) polymer alloys containing iron oxide nanoparticles (Fe3O4 NPs) were developed in this...
Share article
PDMS microspheres as rheological additives for PDMS-based DIW inks
Available online 12 June 2024
Direct Ink Writing holds vast potential for additive manufacturing with broad material compatibility as long as appropriate rheological properties are exhibited by the material of choice. Additives...
Share article
A comprehensive review of fiber-reinforced topology optimization for advanced polymer composites produced by automated manufacturing
Available online 29 May 2024
This review paper focuses on Fiber-Reinforced Topology Optimization (FRTO) methods for automated manufacturing techniques, addressing topology and morphology optimization. Accordingly, the review introduces...
Share article
The role of polysaccharide-based biodegradable soft polymers in the healthcare sector
Available online 11 May 2024
Bio-based polymers have garnered significant interest across the manufacturing industry, global economy, and various engineering disciplines such as packaging, tissue engineering, controlled drug delivery,...
Share article
Production and hosting by Elsevier on behalf of KeAi Communications Co. Ltd